• 2-5/16″ Adjustable Coupler with Safety Chains and Breakaway Kit
• Single Speed Jack
• 8′ Long with 2′ Tapered Nose
• .040 One Piece Aluminum Roof Sheet
• Full Length Side Slats with Two Air Spaces and Natural Smooth Sheets
• Rubber Torsion Axles with Electric Breaks
• Radial Tires with Steel Wheels
• Front Tack with Straight or Slant Wall
• Full-Width Rear Gate with 1/2 Slider and Pipe Hardware
• 4″ Rubber Docking Bumper
• Escape Gate (Streetside or Curbside)
• Dressing Room Door with Hehr Window (Streetside or Curbside)
• 7-Way Plug and Wiring
• Recessed Exterior Light Switches
• Hehr 19″ x 34″ Nose Windows
• LED Turn Signals at Rear
• LED Dome and Clearance Lights

• Center Gate
• Marine Grade Aluminum Treadplate Floor

• Show Cattle – 7′ to 102″ Width, 20′ to 32’+ Length, 6’6″+ Height

• 13,500 BTU A/C Unit with Heat Strip
• 13, 500 BTU Low Pro A/C Unit with Heat Strip and Thermostat
• Frame for A/C
• Frame and Pre Wire for Future A/C Unit

• Ridewell Semi-Style Air Ride
• STI Cargo Max Air Ride
• EZ Lube Axles
• Oil Bath Axles
• Block Axles 2″ and Lower Fenders
• Taper Inner Fenders
• Brush Fenders
• Battery and Boxes
• Single Battery Box
• Single Battery Box with Battery
• Dual Battery Box
• Dual Battery Box with (2) Batteries
• 3′ Carpeted Boot Box with Lid
• Full Width Carpeted Boot Box with Dual Lids
• 4′ Carpeted Boot Box with Lid
• Full Width Padded Boot Box with Dual Lids

• 2-5/16 Fulton Cable Release
• King Pin Coupler on Inner Pipe

• Breaker Box, (1)110v Outlet and Shore Plug
• Additional 110v Outlet
• Shore Power Cord, 30amp or 50amp
• Voyager IR Color Camera Systems

• Add Footage to Stock Area
• Delete Footage from Stock Area
• Add Footage to Dress

• Hayrack with Aerodyne Nose and Tie Rails
• Enclosed Haypod with Aerodyne Nose

• Rubber Floor Mats
• WERM Flooring

• Chute Rack on Side of Trailer
• Panel Rack on Side of Trailer
• Saddle Racks
• Saddle Racks located on Tack Door
• Swingout Saddle Racks
• Hat Shelf
• Water Tanks
• Water Tank with Pump
• Waterers
• Misters
• Bridle Hooks
• Brush Trays
• Hehr Windows (Multiple Sizes and Types)
• AM/FM/CD with Inside, Ouside and Stock Area Speakers

• Paint Top Rail
• Paint Top Rail and Bottom GN Rail
• Paint Drop Gussets
• Paint Smooth Sheets
• Paint Side Slat
• Paint Bottom Rail
• Paint Coupler
• Paint Landing Gear and Handle
• Paint Rear Corner Posts and Rear Header
• Paint Door or Ramp

• Adjustable Pens (50/50 and 60/40)
• Split Pens
• Add 12″ Height to Standard Pens
• Low Latches on Pen Gates
• Feeder Bracket Rods
• 60/40 or 50/50 Removable Pens with Removable Full Height Posts

• 48″ Tall Spring Loaded Rear Ramp
• 52″ Tall Spring Loaded Rear Ramp
• Full Height Spring Loaded Side Ramp

• Insulate and Line Roof and Top Rail (Natural Aluminum)
• Insulate and Line Roof and Top Rail (White)

HWH Hydraulic Slide Out

• 6″ Butterfly Vent
• Lunar Dome Roof Vent
• Two-Way Roof Vent

• Rubber, Double Wall, and Insulate Stock Walls
• Line and Insulate Dress Walls (Natural Mill Finish)
• Line and Insulate Dress Walls (White)

• 7′ (Standard), 7’6″, 8′, 100″ and 102″

Domestic 2 Step Awning

• Electric / Hydraulic Brakes
• Electric / Hydraulic “Disc” Brakes
• Carpet
• Carpet Walls in Gooseneck
• Carpet Side Walls in Dress
• Carpet Bulkhead Wall in Dress
• Line/Insulate/Carpet Side Walls in Dress
• Line/Insulate/Carpet Walls in Gooseneck

• Clothes Rod (5 Feet)
• Clothes Rod (5+ Feet)

Add Horse Divider

• Double Side Tack Doors with Single Pipe Hardware
• Double Side Tack Doors with Internal Latch, Camper Latch, and Combo Lock
• Walk Thru Door in Bulkhead Wall
• Access Door in Gooseneck
• Side Access Door
• Additional Dress Door
• Make Standard Dress Door Wider (37″ to 50″)

• Pre-Painted White Exterior Skin (Standard)
• Pre-Painted Black Exterior Skin
• Pre-Painted Gray Exterior Skin
• Pre-Painted Red Exterior Skin
• Custom Painted Exterior Skin
• Mill Finish (Natural) Exterior Skin
• Stainless Steel Nose Sheets
• Stainless Steel Nose and Gooseneck Side Sheets
• Stainless Steel Side Sheets
• Polished Slat
• Polished Fenders
• Polished Top Rail
• Polished Bottom Rail
• Polished Door Frames and Flush Mount
• Polished Rear Corner Posts and Rear Header
• 2″ Air Space Above Fenders
• Hinged Slat to Cover Air Gap
• Smooth Skin with Hehr Drop Down Windows in lieu of Air Spaces

• Drop Down Gate
• 2 Swinging Gates with Permanent Post in Nose

• 1/2 Slide Gate Inside Center Gate
• 1/2 Swing Gate Inside Center Gate
• 3/4 Swing Gate Inside Center Gate
• Full Swing Gate Inside Center Gate
• Additional Center Gates
• Additional Center Gates Settings
• Slide Rail for Center Gates
• Slam Latch on Swing Gates on Slide Rail
• Make Center Gate Slide Between Fenders (Slide Rail Gates Only)
• No Step 1/2 or 3/4 Swing Gate Inside a Center Gate (Slide Rail Gate Only)
• Run Center Gate at Slant (with Stock Trailer Slam Latch)
• Flow Thru Bars Top of Center Gate (Replaces Slats and Air Spaces)

• Make Standard Escape Gate Wider (37″ to 50″)
• Sliding Escape Gate (Slides on Outside of Trailer)
• Add Single Pipe Hardware to Escape Gate
• Frame and Seal Escape Gate
• Additional Escape Gate

• Full Width Rear Gate (No 1/2 Slider)
• Full Width Rear Gate with Roll Up Gate
• Double Rear gates with Double Pipe Hardware
• Exterior Safe Load Spring Loaded Slant Latch (Full Width Rear Gates)
• Double Swing Full-Width Rear Gate with Double Pipe Hardware (Gate will open Streetside or Curbside)

6’6″ (Standard) with Options to Increase Height in 6″ Increments (6′ Available, Removes Nose Windows)

• Spring Loaded Jack
• Single 2-Speed Jack
• Dual Single Speed Jack
• Dual 2-Speed Jack
• Hydraulic Single-Leg Jack
• Dual Hydraulic Jack

• Clear Lens LED Clearance Lights
• LED Running Lights on Bottom Rail
• Add Standard LED Dome Lights (390 Lumens)
• LED 6″x18″ Dome Lights (880 Lumens)
• Extra LED Turn Signals Mounted in Slats
• Porch Light
• Additional LED Clearance Lights
• Backup Lights
• 3/4″ LED Button Lights (Replace Standard Lights)
• Extra LED Turn Signals Mounted in Fender
• Halogen Load Lights
• Halogen High-Intensity Load Light
• LED Load Light (1042 Lumens)
• LED Scene Load Light
• LED High Turn on Rear
• LED Dome Light Place Under Nose
• Recessed Lighted Sign for Nose (Lettering Not Included)
• LED High Turns on Rear

• V Nose
• Raise Standard Drop Height from 49-1/2″ to 52-1/2″
• Enclose Under Nose with 3 Doors
• Enclose Undernose with Roll Up Door
• Enclose Under Nose with Full Width Lift Door with (2) Access Doors in Lift Up

• Plexiglass and Track (Rear and Escape Gates)
• Plexiglass and Track Only (Rear and Escape Gates)
• Plexiglass (Sides)
• Plexiglass Storage Under Gooseneck
• Plexiglass Storage in Gooseneck
• Plexiglass Storage Box (Mounted Inside)

• 8″ Fold Up Camper Step
• 12″ Fold Up Camper Step
• Step Cleats

• Welded Trailer Ties (Interior)
• Bolted Ties (Exterior)
• Bolted Stainless Steel Ties (Exterior)
• Tie Rails (Interior)
• Outside Tie Rails (Polished or Unpolished)

All Elite built doors are engineered with heavy duty, proprietary extrusions and constructed to allow for maximum seal.

Elite built drop down bar mechanism is machined to allow ease of use. Independent from the drop down door allows for simple use.

Elite utilizes LED interior and exterior clearance lighting in all wiring harnesses. All wiring connections are plugs or are soldered, covered with heat shrink material.

With multiple divider types, the Elite divider is built with designed extrusions that give it maximum strength.

.090″ smooth sheet welded on to our heavy duty wall posts.

With 4 tiers of protection, Elite Horse Trailers provide the protection from horses kicking and pawing, and help prevent sidewall damage and exterior dings.

Elite uses Dexter Rubber Torsion axles with electric brakes and name brand tires. Our trailers are engineered with accurate weights that provide proper axle and tire size based on the total weight of the trailer and it’s contents, including living quarters.

Elite’s proprietary, heavy duty, extruded hinge is used for doors and dividers. This hinge is fitted with a brass fitting that lubricates and allows for a tighter fit with the stainless pin. This hinge is welded to the structure to give us the strongest hinge possible.

Elite only uses HEHR windows. Available in many sizes and types, you can rest assured that they will be installed, worry free.

The Elite built carpeted saddle racks are designed to hold a large variety of today’s saddles.

The wall rubber on our trailers is corded rubber matting that is able to absorb impacts that would damage lesser made products.

Marine grade carpeting is used in the tack room and other applications to assure a long life.

Continuous 5″ radius rail with an overall height of 8″ and a material thickness of 3/16″ with an integrated drip rail.

3/16″ thickness, welded one piece gussets which add structure to provide maximum nose strength.

3/16″ thickness with an engineered break on the top and bottom adds strength and allows for a cleaner weld area to ensure against leakage.

Elite’s floor structure consists of 4″ I beams with an upper 2 1’2″ flange and a lower 3″ flange on 12″ centers. Elite utilizes a .125″ thick, 5052 marine grade sheet floor on top of the structure.

The rear frame is supported by a 2 1/2″ x 5″ upper header at a 1/4″ thickness. For added strength, the rear frame side post is integrated through the floor into the bottom rail.

6005 T6 aluminum alloy posts with 7″ posts at the drop wall, 5″ x 1 3/8″ at doors and dividers, and 1 3/8″ x 2 1/2″ for all other side wall structure posts. The exterior, 6063 aluminum interlocking extruded slat is .125 thick. Exterior smooth sheets are a 3004 aluminum alloy with a H291 temper and thickness of up to .063″.

1″ x 2 1/2″ arched roof bows with one piece, .040″ thick 3003 H16 aluminum roof sheet.